Loading...
Home>HELP - FAQ's>Decal Installation Instructions


Most decals can be made in any color listed above or on the color chart.

Decal Installation Instructions

Standard Decal Installation Instructions

Below are installation instructions for STANDARD decals.  If your decal was made with Bumper Sticker Material (no application tape over the top), Static Cling vinyl or Wall Vinyl then your decal will not have application tape over the decal.  Please see the information at the bottom of this page for your decal installation.

*PLEASE READ -- The decal is covered with a clear “application tape” that allows you to transfer the decal to the application surface. To make sure the decal will stick to the application tape (and not the paper), apply pressure to the entire decal using a squeegee, credit card, plastic spatula or your finger.

Thoroughly clean the area where the decal is to be applied using a non oil based cleaner; warm soapy water works fine. Allow time to dry.  You may wish to use rubbing alcohol on the application surface to make sure that it is cleaned of all chemicals.

Trim around the decal if necessary using scissors or an Exacto knife. Make sure to use the decal itself to center or level the decal since the application tape may not be perfectly cut. Be careful not to cut the decal or YOURSELF!

Peel the paper backing off. This is done easiest by placing the decal FACE DOWN on a flat surface.  Then peel the paper backing off making sure the decal sticks to the application tape that is on the front of the decal.

Position the decal where you would like to place it. Be sure to level the DECAL since the application tape may not be level with the decal. DO NOT use any pressure yet. If the decal is not level, centered, etc. you may reposition it if you have not applied pressure.

Once the decal is where you want it, apply pressure to all of the decal. You may use a squeegee or your fingers.  A credit card, plastic spatula or something similar will work in place of a squeegee.

Now it is time to remove the application tape. Start at a corner and slowly pull back, PARALLEL to the surface. DO NOT pull away from the surface.

Helpful Tricks

If you have a 2 color/layered decal, wet installation can be used for the top layer for proper placement but is not required.  For a wet install simply spray down the the installation surface (decal that has already been installed) using a spray bottle filled with water and a VERY small amount of liquid soap.  Also spray down the backside of the decal you are installing as you remove the paper backing.  Now position the decal where you want it withOUT applying pressure.  Once it is aligned use a squeegee or equivalent to remove all the water.  After you have allowed the decal to dry (a heat gun or hair dryer speeds up the process) remove the application tape.

A heat gun or hair dryer can be use to “stretch” the decal around curved surfaces. Be careful not to overheat the decal as it can burn. This may be used in wet or dry installation.

Small bubbles can be squeegee’d to the edge of the decal. For larger bubbles you may use a pin to pop them and then apply pressure.

For extra durability clear fingernail polish can be added to the corners of the decal. This is highly recommended for decals that have small points (such as flames) or automotive (outdoor) decals.

Shadows are made by first applying the shadow color to the surface FIRST and then applying the main color slightly offset to the shadow color. Slightly above and to the left is the most popular but any variation looks great.

For precision installations with PICTURES make a selection below.

Pick the shape below that best describes your decal.

Top Hinge Method
For decals that are square or round in shape
(about equal height and width)
Center Hinge Method
For decals that are wide but not very tall
(long and narrow)

For Decals made with Bumper Sticker Material:
bullet Simply peel off the paper backing and apply the decal.
bullet Standard installation instruction above are good for reference but your decal will not have applications tape over the decal so ignore those parts.

For Static Cling vinyl decals:
bullet It is CRITICAL that the surface is COMPLETLY clean in order for the decal to stick.  The surface must be a smooth like glass or paint in order for the decal to stick.  Once the surface is clean and dry simply peel and stick the decal; squeegee out any air bubbles by starting in the center and working your way out.  Decal can be pulled off and repositioned if necessary.
bullet Standard installation instruction above are good for reference but your decal will not have applications tape over the decal so ignore those parts.

For Wall Decal Material:
bullet Thoroughly clean the surface withOUT chemical cleaners.
bullet If the decal was large and came rolled up, lay the decal flat for one day to allow the decal to naturally flatten.
bullet Start by installing short end and working your way down the longest direction.
bullet You may pull the decal off and reapply if necessary but please do so gently.
bullet Squeegee out any air bubbles by starting in the center and working your way out to the edges.
bullet Wipe the decal down with a soft, dry cloth after installation to remove any dust or residue that may have appeared during the application process.

Quick Search

 

Categories

 

Priority Mail Shipping

For ALL U.S. Orders

 

Information

 

My account

Track my order(s):

 
Become a Fan on



Bookmark and Share